Table of Contents

General Abstracts: Electronic, Magnetic and Photonic MaterialsDivision. Session I. CuInSe2/Si Heterojunctions for Photovoltaic Applications (O.Akpa, S. Shoieb, and K. Das). High-Temperature Thermoelectric Behaviors of Highly DensePolycrystalline Nonstoichiometry Tiox Ceramics (Y. Liu, J. Lan,B. Zhang, and H. Zhu). An Experimental Setup and Procedure for Thermal ResistanceMeasurements of a Thermal Interface Material (K. Kalkundri, F.Andros, and B. Sammakia). Materials and Manufacturing Challenges in Hybrid FlexibleElectronics (K. Cooper). Session II. Improved Performance of a Fluorescent Blue Organic LightEmitting Diode with Hole Blocking Materials as Dopants forTransport Layers (G. Samal, K. Unni, S. Bharat, andDeepak). Luminescence of the GaP:N Long-term Ordered Single Crystals(S. Pyshkin, J. Ballato, A. Mura, and M. Marceddu). Opals, Photonic Band Gap Materials, Pleochroic Refraction, andMonochromatic Lasers (M. Stem). Magnetism of a V Monolayer on Nb(001): A First PrinciplesCalculation (A. Ramanathan, and J. Khalifeh). General Abstracts: Light Metals Division. Session I. Alcoa Alumina Refinery Secures Future through ReliabilityExcellence Efforts (J. Kalpoe, and K. Johnson). Aluminium Industry Perspective and Price Outlook (G.Djukanovic). Application of ECAP on Commercial Purity Aluminum (N.Evcimen, Y. Bayrak, and A. Ekerim). Assessment of Casting filling by Modelling Surface EntrainmentEvents using CFD (M. Jolly, C. Reilly, and N. Green). Effective Capital Management - A Case Study (J. Petrolito,and M. Richard). Electrochemical Characterization of the Al-Mg Foamed Materialsin NaCl Solutions (S. Valdez, S. Casolco, and H.Castaneda). Session II. Enhanced Resistance of Ti-alloys against Environmental Attack bya Combined Al- and F-treatment (A. Donchev, M. Schutze, R.Yankov, and A. Kolitsch). Fabrication of Aluminum Foam with New Stabilizer Composited byFly Ashes and Short Copper-Coated Carbon Fibers (P. Chen, H.Luo, L. Wang, and Y. Mu). Material Selection for the Lining of Aluminum Holding &Melting Furnaces (A. Wynn, J. Coppack, and T. Steele). Mechanical Properties and Precipitation Behaviors of Mg-Al-Snand Mg-Zn-Sn Alloys (T. Konno, J. Lee, T. Ohya, H. Son, and H.Jeong). Multi Sensor Data Fusion for Aluminium Cell Health Monitoringand Control (H. Viumdal, R. Yan, M. Liane, B. Moxnex, and S.Mylvaganam). Session III. Multistage Fatigue Modeling for Three Wrought Al Alloys (Y.Xue). Optimised Fatigue Behaviour of Ti-6Al-4V Alloy ComponentsFabricated by MIM (O. Ferri, T. Ebel, and R. Bormann). Production of Aluminum and Its Alloy at Lower Temperaturethrough Direct Electroreduction of Solid Alumina and Mixed Oxidesin Chloride Melt (H. Yin, L. Gao, H. Zhu, F. Gan, and D.Wang). Thermo-Mechanical Characterization of Al-Cu-Mg CompositesReinforced with Diboride Particles (N. Cortes, P. Barrado, S.Hoyos, H. Calderon, and O. Suarez). Session II. Study on the Materials of Rolled Al-Mg-Si Alloy Used for theHigh-speed Trains (K. Ji, G. Yao, Y. Mu, and G. Zu). Session III. Thermodynamic Design of Ultra-Strong Titanium Alloys UndergoingPlasticity Induced Martensitic Transformations (S. Neelakantan,P. Rivera-Diaz-del-Castillo, and S. Zwaag). Upgrade and Electrochemical Reduction of TiO2-Rich Slag toTitanium (Q. Xu, L. Sun, Q. Song, W. Xing, J. Du, and Z.Xi). Wear Behaviour of the Newly Developed Biomedical Beta TitaniumAlloy (Ti-23Nb-0.7Ta-2Zr-1O) (S. Sathish, M. Venkatesh, M.Geetha, R. Asokamani, and T. Nandy). General Abstracts: Materials Processing and ManufacturingDivision. Welding. Correlation between Shoulder Flow Zone Quality and Material FlowQuantity during Friction Stir Welding of Thick Aluminum SectionUsing Scroll Shoulder Tool (D. Yan, Z. Chen, and G.Littlefair). Forming and Machining. Effect of AWJ Machining Processes on Flexural Properties of CFRPComposites (T. Briggs, and M. Ramulu). New High Strength Ductile Bainitic Forging Steels (C. Keul,M. Urban, M. Fischer, G. Hirt, and W. Bleck). Superplastic Blow Forming of Steel and Titanium Alloys forAerospace Parts (H. Lee, J. Yoon, and Y. Lee). Cooling Behavior of Lead-Free Bismuth Bronze Produced throughthe Frozen Mold Casting Process (S. Tada, H. Nakayama, T.Nishio, and K. Kobayashi). Microstructure, Characterization, and Modeling. Mathematical Modelling of an Annealing Furnace for ProcessControl Applications (N. Depree, J. Sneyd, S. Taylor, M. Taylor,M. O'Connor, and J. Chen). Synthesis and Processing. Innovative and Integrated Technologies for the Development ofAeronautic Components (N. Gramegna, F. Bonollo, E. DellaCorte,F. Grosselle, and M. Cocco). Thermo-Mechanical Behavior of Chemically Bonded PhosphateCeramic Composites Reinforced with Graphene Nanoplatelets: ASubstantial Material Improvement toward Structural Applications(H. Colorado, C. Hiel, and H. Hahn). Synthesis and Microstructure of Tic/Tin Porous CeramicComposites Processed via Hysycvd/Direct Nitridation (J.Flores-Garcia, and M. Pech-Canul). Cyclic Oxidation Behavior of Detonation Gun Sprayed Ni-20CrCoating on a Boiler Steel at 900degreeC (G. Kaushal, H. Saheet,and S. Prakash). General Abstracts: Structural Materials Division. Fatigue and Fracture. Fatigue Crack Growth Mechanisms of Long and Small Cracks inStructural Materials (A. Gavras, C. Lammi, and D.Lados). Effect of Hydrogen on Crack Nucleation in 316 Stainless Steelunder Rotating Beam Fatigue Loading Conditions (D. Matson, C.Skipper, G. Leisk, and A. Saigal). Effect of Ca, Mg and Ti-Mg Addition on the Impact Toughness ofHeat Affected Zone in Low Carbon Steel (J. Ma, D. Zhan, Z.Jiang, J. Yu, J. He, and H. Shen). Non-Ferrous Materials. Stress-Rupture Behavior of the Single Crystal Superalloy M09A(Q. Zheng, J. Yang, H. Zhang, X. Sun, H. Guan, and Z.Hu). Materials Characterization and Shock Loading. Research on the Thermal Plasticity of the 18Mn-18Cr-0.77N-2MoHigh Nitrogen Austenitic Stainless Steel (L. Wanming, L.Huabing, and J. Zhouhua). An Overview of the Microstructures of High-Strength Two-PhaseNear-Equi-atomic FeNiMnAl Alloys (I. Baker, Y. Liao, X. Wu, H.Wu, M. Miller, K. Russell, and P. Munroe). Was There a Bomb on Mattei's Aircraft? (D. Firrao, and G.Ubertalli). Improvement of Charpy Impact Properties in Heat Affected Zonesof API X80 Linepipe Steels Containing Complex Oxides (H. Sung,S. Shin, W. Cha, K. Oh, and S. Lee). Microstructural Analysis of Separations Occurring during Charpy Impact Test of Linepipe Steels (S. Hong, S. Shin, J.Bae, K. Kim, S. Lee, and N. Kim). Environmental Degradation. Investigation of the Stress Corrosion Cracking of Carbon Steelin Fuel Grade Ethanol Environments (L. Goodman, X. Lou, and P.Singh). Factors Affecting the Environmental Assisted Cracking Behaviorof 2205 Duplex Stainless Steel (K. Chasse, D. Yang, P. Singh,and R. Neu). Hydrogen Embrittlement of a Bainitic Wheel Steel (R.Xuechong, L. Fenbin, S. Yanjing, and C. Wuyang). General Poster Session. Session I. Annealing Behavior of TiO2-sheathed Ga2O3 Nanowires (C. Lee,H. Kim, C. Jin, J. Jun, C. Hong, and J. Kang). Deformation of High Purity Copper Specimens in Compressionbetween Flat and Grooved Dies (B. Raddad, T. Al-hashani, and M.Abdel-Rahman). Structure and Thermal Oxidation Properties of RuAl And Ru-Al-TiAlloys Prepared by Mechanical Alloying (M. Clisson, J. Gaudet,L. Roue, and D. Guay). Study on Magnetic-Gravity Combination Separation and AcidLeaching of a High Phosphorus Fine Hematite (T. Jiang, L. Yang,and Y. Guo). Silver Recovery from Waste Radiographic Films Using DifferentMethods (H. Morcali, S. Aktas, and O. Yucel). Dissolution of Platinum from Scrap Automotive CatalyticConverters Using a Combination of HCl+H2O2 (C. Uysal, S. Aktas,E. Kizilaslan, and K. Sesen). Study on Visible Light Photocatalytic Performance of NanoTungsten Trioxide (W. Daoxin). Plasma-Polymerization of Hexamethylcyclotrisiloxane UsingAtmospheric Pressure Dielectric Barrier Discharge (G. Kim, andY. Kim). The Effects of Nickel in Oxide Layers on the AZ91 Mg AlloysSynthesized by Plasma Electrolytic Oxidation (D. Shin, K. Shin,I. Hwang, D. Lee, and B. Yoo). Development of Ultrasonic Techniques for Process Control in Ironand Steel Making (J. Pandey, M. Raj, K. Balasubramaniam, and N.Bandyopadhyay). Enhancing Mineral Beneficiation by High Intensity PowerUltrasound (J. Pandey, M. Raj, M. Sinha, and N.Bandyopadhyay). Rotary Ultrasonic Drilling of Al2O3 Ceramic Material (B. Rao,P. Laxminarayana, and M. Ramulu). EDM and AWJ Edge Finishing on Surface Morphology of HybridComposite Laminates (P. Laxminarayana, V. Isvilanonda, M.Ramulu, and B. Rao). Microstructures and Mechanical Properties of AM60B-based Eco-MgAlloys (M. Choi, D. Jang, and S. Kim). Oxidation and Ignition Resistances of AM60B-based Eco-Mg Alloys(I. Kim, J. Seo, and S. Kim). Effect of Fabrication Parameters on Morphology of Porous KaolinCeramics (M. Keshavarz, and A. Barzegar). Preparation and Characterization of Nanocrystalline SilverParticles (B. Ebin, E. Yazici, S. Gurmen, and B.Ozkal). Aerosol Route Synthesis of Copper Oxide Nanoparticles UsingCopper Nitrate Solution (B. Ebin, O. Gencer, and S.Gurmen). Facile Synthesis of Hollow Co3O4 Microspheres by SolutionSpray-Oxidation Method and Its Properities as Supercapacitors(G. Qiusong, D. Guangrong, and G. Xueyi). Impact toughness Enhancement of an Electron Beam WeldedTi-6Al-4V Titanium Alloy through Post-Welding Heat Treatment (C.Buirette, and J. Huez). Interfacial Reactions of Pure Sn, Sn-3.0Ag-0.5Cu and Sn-9.0ZnLead-free Solders with the Fe-42Ni Substrate (Y. Hsieh, Y. Yen,and C. Jao). Quality of Slab Ingots and Heavy Plates Produced by a 40t ESRFurnace (X. Geng, and Z. Jiang). Production of Titanium Carbide Reinforced Titanium MatrixComposites via Powder Metallurgy Method (B. Karaduman, O.Meydanoglu, H. Cimenoglu, and E. Kayali). Properties and Performance of Composites Based onSuperrefractories Cements (I. Nickolai, and T.Valentina). Surface Treatment of Materials by Low Energy High Current PulsedElectron Beam under Evaporating Mode (K. Zhang). Deformation Field and Microstructure of Copper in Flat PunchIndentation (M. Hudspeth, T. Murthy, C. Saldana, and S.Chandrasekar). Laser Beam Welding of Haynes 188 (A. Odabasi, N. Unlu, G.Goller, and N. Eruslu). Microstructure Components and Mechanical Properties of anAcicular Ferrite Pipeline Steel (W. Wang, Y. Shan, W. Yan, andK. Yang). Grain Boundary Character Distribution and Mechanical Property ofan as Cold Rolled High Nitrogen Austenitic Stainless Steel (W.Yan, Y. Shan, K. Yang, and W. Wang). Comparison of Stress Corrosion Cracking and HydrogenEmbrittlement Resistance of High Strength Aerospace Alloys (D.Wert, and T. Werley). Corrosion Behavior of Al-Si-Cr-Ni-Cu Bearing Low Carbon Steel inA Cyclic Dry/Wet Laboratory Test (D. Zhan, H. Zhang, S. Bai, andZ. Jiang). Microstructure Changes in Primary Recrystallization ofGrain-Oriented Silicon Steel by Pulse Current IntermediateAnnealing (L. Liu, Q. Xia, W. Shi, L. Li, X. Wu, Q. Zhai, and W.Zeng). Effect of Particle Size on the Microstructure of RapidlySolidified Hypereutectic Iron Alloy Powder (M. Yang, Y. Dai, C.Song, and Q. Zhai). Effect of Nitrogen Addition on Isothermal Phase Transformationand Mechanical Properties in Biomedical Co-Cr-Mo Alloys (S.Kurosu, H. Matsumoto, and A. Chiba). Different Tempering Precipitation Behaviors of Carbide in2.25Cr-1Mo-0.25V Steel After Quenching and Normalizing (Z.Yongtao, Z. Sixin, W. Xiaojun, Z. Hanqian, and L. Jinfu). Microstructure Development of Silicon Steel Prepared byNear-Rapid Solidification (X. He, Q. Sun, L. Wang, Q. Peng, andQ. Zhai). Small Punch Creep of Service-Exposed SUS 316 HTB SuperheaterTubes of Fossil Boilers (M. Saucedo-Munoz, S. Komazaki, T.Hashida, T. Takahashi, V. Lopez-Hirata, and T. Shoji). Phase Decomposition during Aging in an Al-22wt.%Zn Alloy (L.Melo-Maximo, D. Melo-Maximo, S. Lezama-Alvarez, E. Avila-Davila, V.Lopez-Hirata, O. Soriano-Vargas, and J.Gonzalez-Velazquez). Fatigue Life Prediction for Notched Structures using MechanisticMultistage Fatigue Model (Y. Xue, B. Jordon, and M.Horstemeyer). Development of Alloys on an Iron Basis (Z.Zhumadilova). Finite Element Analysis of Residual Stress of Plasma-SprayedCoatings on Thick Wall Components Based on Nastran Software (L.Niu, T. Zhang, G. Shi, Z. Dou, J. He, and X. Cao). Preparation of Iridium Fine Particle by the Effect of GrindingAdditive, Nacl (Y. Kim, Y. Ham, and J. Lee). Evaluation of High Energy Milling Behavior of ZnO Powders inDifferent Milling Conditions (S. Yakar, A. Soyler, B.Ozkal, S. Gurmen, and M. Ovecoglu). Quality Control of the Refining Process at Electron Beam Meltingand Development and Implementation of Engineering Support Systemfor Process Modeling and Control (E. Koleva, G. Mladenov, I.Batchkova, K. Velev, V. Vassileva, and K. Vutova). Sintering Densification and Microstructural Characterization ofMechanical Alloyed Fe-Mn-Si Based Powder Metal System (A.Soyler, B. Ozkal, and L. Bujoreanu). Effect of Non-Sinusoidal Oscillation Parameters on LiquidFriction and Lubrication Near the Meniscus of Slab ContinuousCasting Mold (X. Meng, and M. Zhu). Magnetic Properties of High-Coercivity NanocrystallinePr-Fe-Co-Al-B Bulk Amorphous (L. Bessais). Water Modeling Study on the Behavior of Inclusions in aGas-Stirred Ladle with Two Tuyeres (S. Zheng, X. Chen, J. Hu,and M. Zhu). Effect of Niobium on Solidification Structure of Gray Cast Iron(Z. Wenbing, Z. Hongbo, Z. Dengke, H. Qin, and Z.QiJie). Synthesis of Ag/ZnO Nanocomposite Particles by Ultrasonic SprayPyrolysis Method (S. Gurmen, and B. Ebin). Fatigue of Hybrid Polymeric Composites on Twisting (N.Chikhradze, L. Japaridze, G. Abashidze, and L. Okijava). Influence of Parameters on Process Performance during ElectroDischrge Maching of Inconel-718 (S. Rajesha, A. Sharma, and P.Kumar). Simulation of Dislocation Interaction with Precipitates (P.Jing, H. Lee, J. Shim, I. Robertson, and B. Wirth). Electrochemical Formation of Mg Li-Y Alloys at SolidMagnesium Electrode from Licl Kcl Ycl3 Melts (P.Wang, H. Lu, and F. Shi). Electrochemistry of Tantalum Pentachloride in the RoomTemperature Ionic Liquid 1-Butyl-3-Methy ImidazoliumHexafluorophosphate (P. Wang, H. Lu, and F. Shi). Author Index. Subject Index.

About the Author

Headquartered in the United States but international in both its membership and activities, The Minerals, Metals & Materials Society (TMS) is a rare professional organization that encompasses the entire range of materials and engineering, from minerals processing and primary metals production to basic research and the advanced applications of materials.